Ecompass LLP

Advanced Motor Drivers Supporting Analog, PWM, RC, and Serial control signals. Overvoltage | Overcurrent | Overtemperature | Low Battery Warning for enhanced Protection

 

Versatile controllers supporting Analog, PWM, RC, and Serial inputs with built-in Overvoltage, Overcurrent, Overtemperature, and Low Battery Warning protections.

16-Channel 12-bit PWM/Servo Driver I2C interface PCA 9685 for Arduino Raspberry Pi

If you want to make a robot that has lots of moving parts or if you want to control too many LEDs with PWM outputs,  then the limited PWM outputs of your microcontroller would be a big problem for you. To overcome this problem, the only thing you should do is to get a 16-Channel 12-Bit PWM/Servo Driver.

You can control 16 free-running PWM outputs with a 16-Channel 12-Bit PWM/Servo Driver using only 2 pins. You can even chain up 62 breakouts to control up to 992 PWM outputs.

It’s an I2C-controlled PWM driver with a built-in clock. That means you do not need to continuously send it to signal to tie up your microcontroller, it is completely free running!

It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs. This is good when you want to control white or blue LEDs with 3.4+ forward voltages. 6 address select pins so you can wire up to 62 of these on a single I2C bus, a total of 992 outputs.

Features :

1. Adjustable frequency PWM up to about 1.6 KHz
2. 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate
3. Configurable push-pull or an open-drain output
4. The output enable pin to quickly disable all the outputs
5. Terminal block for power input
6. Reverse polarity protection on the terminal block input
7. Green power-good LED
8. 3 pin connectors in groups of 4 so you can plug in 16 servos at once
9. Chainable design
10. A spot to place a big capacitor on the V+ line
11. 220-ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial.
12. This board/chip uses I2C 7-bit address between 0x60-0x80, selectable with jumpers.

12Volt N20 Mini Motor

This N20-12V Micro Metal Gear Motor has small volume, torsion big, all metal gear, durable, not easy to wear. Great replacement for the rusty or damaged DC geared speed reduce motor on the machine. Widely used on Boat, Car, Electric Bicycle, Fan, Home Appliance.

The N20 Micro Gear 12V DC Motor (High Torque) is lightweight, high torque, and low RPM motor. It is equipped with gearbox assembly so as to increase the torque of the motor. It has a cross-section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter. It has a very small size so as fit in complex spaces of small-scale application. One can connect this Micro Gear Motor to wheels to drive them from one place to other while carrying high loads.

This N20 Micro Gear 12 V DC Motor (High Torque) has small volume, torsion big, all metal gear, durable, not easy to wear. Great replacement for the rusty or damaged DC geared speed reduce motor on the machine. Widely used on Boat, Car, Electric Bicycle, Fan, Home Appliance.

Note: Image of product may differ from Actual Product.

28BYJ 48 5V Stepper Motor with ULN2003 Driver Board

The 28BYJ-48 Stepper Motor and ULN2003 Stepper Motor Driver is a widely popular combination of the stepper motor and stepper driver, because of the stability and reliability of the system.

28 BYJ 48 is the most commonly used stepper motor because of its compact size, 5V power supply (that can be provided by any controller), and high level of control.

ULN2003 Driver Module Stepper Motor Driver Board for driving and controlling stepper motors.ULN2003 Stepper Motor Driver Board uses the ULN2003 DARLINGTON ARRAYS to drive the 4-phase 5-wire stepper motor (5v-12v). The 5 Line 4 Phase can be driven by an ordinary ULN2003 chip that can also be connected to the phase 2 development board used for supporting the use of a direct plug and easy-to-use stepper motor used in the development board. A, B, C, D four-phase LED indicates the status of the stepper motor work.

These stepper motors consume high current and hence a driver IC like the ULN2003 is mandatory. The main purpose of ULN2003 is to amplify the control signals from the Arduino, so as to drive the 28BYJ-48 Stepper Motor. If you will give the ULN2003 stepper driver a certain pulse signal, it will drive the step motor to a certain angle. The control of the Stepper Motor movement angle is done by controlling the number of stepper motor driver pulses. The speed of the stepper motor rotation is also controllable by controlling the frequency of the pulses.

Features:

• XH-5P socket can be connected directly to a 28BYJ-48 Model stepper motor
• Brand new and high-quality product.
• Stepper motor with a standard interface, when used directly pluggable.
• A, B, C, D four-phase LED indicator which indicates the status of the stepper motor work.
• Compact size stepper motor perfect for small robotics applications.

Application:

• DIY robotics projects
• CNC machines and 3D printers
• Machines that need precise control
• Motor and security camera
• DVD players

DC Motor 1203 B PWM Speed Controller 6V/12V/24V/28V 3A Board Module Variable

This 1203B PWM 6V 12V 24V 28V 3A DC Motor Speed Regulator allows controlling the speed of a motor with fully adjustable 0%-100%. The motor speed controller can easily provide a continuous current of 3A to your DC motor or other DC load.

Application:

• This PWM Speed controller is for DC 6V 12V 24V 28V Motor.

Pinouts:

• Motor+: Motor Positive Terminal
• Motor-: Motor Negative terminal
• Power+: DC 6V – 28V
• Power-: Gnd

Note:- Do not use it as voltage regulators for other devices like LED's,Lights etc.

PWM Motor Speed Controller, DC 6V 12V 24V 3A PWM Motor Speed Control Reversible Controller Regulator with Switch 1203BB

The 1203BB DC Motor Speed Regulator controls the speed of a DC motor by adjusting Pulse-Width-Modulated (PWM). It provides a continuous current of 3A to your DC motor or other DC load. Besides, the circuit also includes a 3A fuse, with reverse connection of power supply and control the forward or reverse direction and the stop of DC motor by switch.

Features:

- Color: As the pictures show.
- Material: Metal.
- Size: 5 * 3.2 * 1.5cm.
- The input power range is DC6-28V.
- Control the forward or reverse direction and the stop of DC motor by switch.
- Potentiometer with switch function.
- The switch cable length 15cm.

Operating instruction:

Before you attempting to wire the controller, make sure that the power is off.
1. Connect wires refer to the wiring diagram.
2. Turn on the power, and adjust the potentiometer.
3. The LED indicates the power up and the speed of motor.

Note:- Do not use it as voltage regulators for other devices like LED's,Lights etc.

Advanced Motor Drivers Supporting Analog, PWM, RC, and Serial control signals. Overvoltage | Overcurrent | Overtemperature | Low Battery Warning for enhanced Protection

 

Versatile controllers supporting Analog, PWM, RC, and Serial inputs with built-in Overvoltage, Overcurrent, Overtemperature, and Low Battery Warning protections.

Advanced Motor Drivers Supporting Analog, PWM, RC, and Serial control signals. Overvoltage | Overcurrent | Overtemperature | Low Battery Warning for enhanced Protection

 

Versatile controllers supporting Analog, PWM, RC, and Serial inputs with built-in Overvoltage, Overcurrent, Overtemperature, and Low Battery Warning protections.

Advanced Motor Drivers Supporting Analog, PWM, RC, and Serial control signals. Overvoltage | Overcurrent | Overtemperature | Low Battery Warning for enhanced Protection

 

Versatile controllers supporting Analog, PWM, RC, and Serial inputs with built-in Overvoltage, Overcurrent, Overtemperature, and Low Battery Warning protections.

Advanced Motor Drivers Supporting Analog, PWM, RC, and Serial control signals. Overvoltage | Overcurrent | Overtemperature | Low Battery Warning for enhanced Protection

 

Versatile controllers supporting Analog, PWM, RC, and Serial inputs with built-in Overvoltage, Overcurrent, Overtemperature, and Low Battery Warning protections.

Advanced Motor Drivers Supporting Analog, PWM, RC, and Serial control signals. Overvoltage | Overcurrent | Overtemperature | Low Battery Warning for enhanced Protection

 

Versatile controllers supporting Analog, PWM, RC, and Serial inputs with built-in Overvoltage, Overcurrent, Overtemperature, and Low Battery Warning protections.

5A Dual-Channel DC Motor Drive Module, 3V-14V Input, Forward/Reverse Control, PWM Speed Regulation, Double H-Bridge

The 5A Dual DC Motor Driver Module is a compact and efficient solution for controlling two DC motors simultaneously. Designed with a double H-Bridge circuit, it supports forward and reverse motor rotation, making it ideal for robotics, DIY electronics, and other motor-driven projects. With a wide voltage range and PWM speed control, this module offers precision and reliability in motor control applications.

Features

1. High Current Capacity

   • Supports up to 5A current for each channel, ideal for powerful motor applications.

2. Wide Voltage Range

   • Operates with an input voltage range of 3V to 14V, suitable for various motor types.

3. Dual-Channel Control

   • Controls two DC motors independently or simultaneously for versatile applications.

4. PWM Speed Regulation

   • Offers precise speed control using Pulse Width Modulation (PWM) signals.

5. Forward and Reverse Control

   • Enables easy direction control of motors with forward and reverse functionality.

6. Double H-Bridge Circuit Design

   • Ensures stable and efficient motor driving with reliable operation.

7. Compact and Lightweight

   • Small form factor for easy integration into DIY and professional projects.

8. Wide Application Range

   • Perfect for robotics, RC cars, conveyor systems, and automated projects.

9. Easy Interface

   • Simple connections and control interface, compatible with microcontrollers like Arduino, Raspberry Pi, and more.

10. Durable Build

• Built with high-quality components to withstand continuous operation.

This module is a go-to solution for anyone working on projects requiring robust, precise motor control with minimal complexity.

L298 Motor Driver Module | 2A Dual Channel PWM Control

L298 Motor Driver Module, 2A Dual Channel total 4A, PWM Control for motors variable speed, with back EMF protection, versatile for Robotics Arduino Raspberry PI. It is a high voltage, high current, dual full-bridge motor driver designed to accept standard TTL logic levels and drive inductive loads such as relays, solenoids, DC and stepping motors.

• Current Sense for each motor.
• Heatsink for better performance.
• Power-On LED indicator.
• Driver chip: L298 dual H-bridge driver chip.
• Operates up to 35V DC
• Drive part of the peak current Io: 2A / Bridge
• Logical part of the terminal power supply range Vss: 4.5V-5.5V
• Logical part of the operating current range: 0 ~ 36mA
• Maximum power consumption: 20W

NEMA23 57HS76-2804 | 57HD3403-21B Stepper Motor – Round Type Shaft

NEMA 23 is a standard for stepper motors that defines the size and mounting pattern of the motor. The "57x57" specification refers to the physical size of the motor, where the motor faceplate is 57mm x 57mm. Here's an overview of NEMA 23 57x57 stepper motors:

Key Features:

1. Frame Size: 57mm x 57mm (2.24 inches by 2.24 inches).
2. Step Angle: Typically 1.8 degrees per step (200 steps per revolution), though 0.9-degree versions (400 steps per revolution) are available.
3. Holding Torque: Varies by model, but common torque values range from 0.5 Nm to 2.5 Nm, making these motors suitable for high-torque applications.
4. Current Rating: The current per phase can range from 1.5 A to 3.0 A or higher, depending on the model.
5. Voltage Rating: Operates with driver voltages from 12V to 48V, depending on the motor and driver setup.
6. Applications: Widely used in CNC machines, 3D printers, robotics, and other precision motion control systems.

Considerations:

• Driver Compatibility: Ensure you select a stepper motor driver that matches the current and voltage requirements of the NEMA 23 motor.
• Heat Dissipation: Since stepper motors can get hot during prolonged use, adequate ventilation or heat sinks may be required.
• Microstepping: Using microstepping drivers can enhance resolution and smooth out motion for finer control.

NEMA23 57HS76-2804 | 57HD3403-21B Stepper Motor – Round Type Shaft

NEMA 23 is a standard for stepper motors that defines the size and mounting pattern of the motor. The "57x57" specification refers to the physical size of the motor, where the motor faceplate is 57mm x 57mm. Here's an overview of NEMA 23 57x57 stepper motors:

Key Features:

1. Frame Size: 57mm x 57mm (2.24 inches by 2.24 inches).
2. Step Angle: Typically 1.8 degrees per step (200 steps per revolution), though 0.9-degree versions (400 steps per revolution) are available.
3. Holding Torque: Varies by model, but common torque values range from 0.5 Nm to 2.5 Nm, making these motors suitable for high-torque applications.
4. Current Rating: The current per phase can range from 1.5 A to 3.0 A or higher, depending on the model.
5. Voltage Rating: Operates with driver voltages from 12V to 48V, depending on the motor and driver setup.
6. Applications: Widely used in CNC machines, 3D printers, robotics, and other precision motion control systems.

Considerations:

• Driver Compatibility: Ensure you select a stepper motor driver that matches the current and voltage requirements of the NEMA 23 motor.
• Heat Dissipation: Since stepper motors can get hot during prolonged use, adequate ventilation or heat sinks may be required.
• Microstepping: Using microstepping drivers can enhance resolution and smooth out motion for finer control.

Single Shaft BO Motor - Straight (I Shape)

This is an 8mm Single Shaft BO DC Motor Straight "I" Shape. This BO Single Shaft Motor is a Straight motor that provides good torque and rpm at lower operating voltages, which is their main advantage. The combination of a small shaft and matching wheels results in an optimised design for your application or robot. Because of the mounting holes on the body and the light weight, it is suitable for in-circuit placement. This motor is compatible with 69mm Diameter Plastic Gear Motor Wheels.

Features-

• Low density, lightweight, low inertia.
• Capability to absorb shock and vibration as a result of elastic compliance.
• Ability to operate with minimum or no lubrication due to inherent lubricity.
• The relatively low coefficient of friction.

Specification-

* Product Images are shown for illustrative purposes only and may differ from the actual products.

High Torque Low Speed 3.7V-6V Gear Motor for Robotics, RC Vehicles, and DIY ProjectsNote: The motor is Dirty and Rusted.

Description: The 3.7V-6V Small DC Gear Motor is designed for precision-driven applications, offering a compact yet powerful solution for various robotics, RC vehicles, and DIY projects. Its metal gear construction ensures durability and efficient performance, especially in low-power applications where space and weight are concerns. This motor is compatible with small wheels, propellers, or other attachments, making it versatile for multiple hobby and automation needs.

Features:

• Voltage Range: Operates efficiently between 3.7V and 6V DC, allowing for use with various battery types, including lithium and alkaline.
• High Torque Output: Ideal for low-speed, high-torque applications, such as small robots, RC cars, and hobbyist models.
• Metal Gear Construction: Durable metal gears provide a long lifespan and reliable performance, even under load.
• Compact Design: Lightweight and space-saving, perfect for compact electronic assemblies.
• Easy Connectivity: Comes with two color-coded wires (red for positive and blue for negative), simplifying integration with other components.

This motor is ideal for hobbyists, electronics enthusiasts, and students working on small mechanical projects, providing both reliability and ease of use in low-voltage applications.

PJN29ED18CQ 12V 24V Brushed DC Motor PJN29 

This 6-24V DC Brush Motor Round 35.7x75.2mm with 12 Teeth Copper Gear is equipped with the Brushed Motor having RPM 2000-5000, delivering efficient operation and reliable performance. It produces low noise and vibration, making it ideal for use in precision applications.

Please refer datasheet for details.

Note: This is a generic DIY Motor, finishing, weight and size may vary in each stock. Product Images are shown for illustrative purposes only and may differ from the actual products. We suggest you buy a few quantities before going for bulk or contact customer support for current stock images.

PJN29ED18CQ 12V 24V Brushed DC Motor PJN29 

This 6-24V DC Brush Motor Round 35.7x75.2mm with 12 Teeth Copper Gear is equipped with the Brushed Motor having RPM 2000-5000, delivering efficient operation and reliable performance. It produces low noise and vibration, making it ideal for use in precision applications.

Please refer datasheet for details.

Note: This is a generic DIY Motor, finishing, weight and size may vary in each stock. Product Images are shown for illustrative purposes only and may differ from the actual products. We suggest you buy a few quantities before going for bulk or contact customer support for current stock images.

DC6V 12V 18V Large Torque Micro Mini RS 395 Electric Motor Double 2.3mm Shaft Axis

Motor model: 395 motor
Voltage: 6-12V about 7.4V is recommended, 12V rotating speed is too high
No load current: 3.7V 400ma, 6V 440ma, 7.4V 460ma, 12V, 650ma
Speed: 3.7V about 10000turns; 7.4V 20,000 turns

Note: This is a generic DIY Motor, finishing and size may vary in each stock. Product Images are shown for illustrative purposes only and may differ from the actual products. We suggest you buy a few quantities before going for bulk or contact customer support for current stock images.

12 Volt DC Motor RS 775 for DIY

• Operating Voltage: 12V(Recommended Voltage is 12v, Although the motor can run on 24v but we don't recommend it using it on 24V)
• No-load Current: 0.6A
• Maximum Current: 2A
• No Load Speed RPM @12V: Approx ~5000/6000 RPM
• No Load Speed RPM @24V: Approx ~11000/12000 RPM
• Mounting Screw Hole Diameter: ~4 mm
• Distance between Screw Holes: ~33 mm
• Diameter of the Motor: 41mm(Without metal clip)
• Length of the Motor (Body): 67mm
• Length of shaft: ~16-20 mm(Veries with Every Lot but usually lies in this bracket)
• Motor Shaft Diameter: 5mm
• Main Color: Silver Tone

Note: This is a generic DIY Motor, finishing, weight and size may vary in each stock. Product Images are shown for illustrative purposes only and may differ from the actual products. We suggest you buy a few quantities before going for bulk or contact customer support for current stock images.

Note:- There is no surety of the presence of an inbuilt fan inside the motor body as it varies with every new stock and  we ship it randomly according to availability.

DIY 12 Volt DC Motor Approx 3.5cm-DIA

Introducing our high-quality 545 DC Motor, engineered to provide reliable and efficient performance for a wide range of applications. This versatile motor is designed to meet the demands of various projects, offering consistent power and durability.

The 545 DC Motor offers easy customisation and compatibility with a variety of accessories and gears. This allows you to fine-tune your project and achieve optimal performance. Its versatile design makes it suitable for a wide range of applications, including DIY enthusiasts, students, and professionals alike.

Installing and connecting the 545 DC Motor is a breeze. It features user-friendly wiring and mounting options, making it simple to integrate into your project. The motor's compact size enables it to fit in tight spaces, providing flexibility in design and installation.

Whether you're building a robot, creating a model car, or working on any other project that requires reliable motor power, our 545 DC Motor is your ideal choice.

Features :- 

• Reliable Performance: The 545 DC Motor is engineered to deliver consistent and reliable performance for a variety of applications.
• Versatile Applications: This motor is suitable for a wide range of projects, including robotics, automation, model making, and DIY creations.
• Compact and Robust Design: With its compact size and robust construction, the 545 DC Motor provides excellent torque and speed capabilities.
• Wide Voltage Range: The motor operates on a wide voltage range, allowing for easy integration with different power sources and systems.
• Durable Construction: Built with high-quality materials, the motor is designed to withstand heavy use and demanding environments, ensuring long-lasting performance.
• Energy Efficient: The motor's efficient design minimizes energy consumption, making it an energy-saving option for your projects.
• Customisation Options: The 545 DC Motor is compatible with various accessories and gears, providing flexibility for customisation to suit specific project requirements.
• Easy Installation: The motor features user-friendly wiring and mounting options, making it simple to install and integrate into your project.
• Precise Control: With its reliable performance, the motor offers precise control over rotational speed and torque, ensuring accuracy in your applications.
• Quiet Operation: The motor operates with reduced noise levels, providing a quieter working environment for your projects.

Dimensions and Ratings:

37B520-648-1207 High-Performance DC Gear Motor With D Shaft | Operating 6V to 24V For Projects Requiring a Reliable and Efficient

The DC Geared Motor is a high-quality motor for applications requiring reliable torque and speed control. This motor features a robust design with precision gears that ensure smooth operation and enhanced durability. It is ideal for use in robotics, automation, conveyor systems, and other projects that demand consistent performance. The motor's compact size and efficient power consumption make it suitable for both hobbyist and industrial applications.

Operating on DC voltage, this geared motor offers a balance of speed and torque, making it perfect for various mechanical projects where accurate movement is essential. The motor is easy to install and integrate into different systems, providing flexibility for diverse project requirements.

Features

1. High Torque Output: High-quality offers a strong torque performance.
2. Compact Design: The motor's compact size allows for easy integration into space-constrained projects.
3. Voltage: Typically operates at 12V (may support a range from 6V to 24V).
4. Precision Gears: Ensures smooth operation and extends the motor's life span.
5. Efficient Power Consumption: Designed for optimal performance with minimal power usage.
6. Versatile Applications: Suitable for robotics, conveyor belts, automation systems, and other mechanical projects.
7. Reliable DC Motor Operation: Provides consistent and stable performance for various tasks.
8. Durable Construction: Built with high-quality materials for long-lasting use.

Premium Quality Multiple RPM DC Gear Robotics Motor 12v 6mm Black

Discover our Center Shaft DC Geared Motors, engineered with metal gears to deliver exceptional performance. Our DC motors feature a threaded 3mm drill hole in the middle of the shaft, simplifying connectivity to wheels or other mechanical assemblies.

These standard-sized DC motors are incredibly user-friendly and cost-effective, working seamlessly with an Arduino or compatible board. Our 12Volt DC motors boast a voltage range of 5 to 35V DC, making them suitable for all-terrain robots and an array of robotic applications.

Experience easy connectivity with our motors thanks to the internally threaded shaft and nut, enabling straightforward assembly with wheels and other components. Upgrade your robotic systems today with our efficient and reliable DC-geared motors.

Specifications:

• RPM: Multi RPM(3.5|30|45|60|100|150|200|300|500|750|1000).
• Operating Voltage: 12V DC Max.
• Gearbox: Attached Plastic (spur)Gearbox
• Shaft diameter: 6mm with internal hole
• Torque: 1 kg-cm 
• No-load current = 60 mA(Max)
• Load current = 300 mA(Max).

Features:

1. Our product boasts premium-quality gears, designed for optimal performance and durability.
2. Our metal gears are specially engineered for exceptional wear and tear resistance, ensuring long-lasting use.
3. The gearbox is expertly sealed and lubricated with lithium grease, offering a maintenance-free solution for your needs.
4. Our motor is versatile and adaptable, operating seamlessly from 4V to 12V and delivering a wide range of RPM and torque, with a maximum of 10 RPM at 12V.
5. The shaft features a carefully crafted hole, enabling effortless coupling to other components and ensuring seamless integration into your robotic systems.

Upgrade your robotic systems with our reliable, high-performance motor today.

Note:
1. For the desired RPM result we recommend operating this motor on 9v DC. 

2. The color, sticker, and packaging on the product may vary in each lot. We ship randomly.

Package Includes:

1 x Premium: 12V Centre Shaft DC Geared Motor

Premium Quality Multiple RPM DC Gear Robotics Motor 12v 6mm

Discover our Center Shaft DC Geared Motors, engineered with metal gears to deliver exceptional performance. Our DC motors feature a threaded 3mm drill hole in the middle of the shaft, simplifying connectivity to wheels or other mechanical assemblies.

These standard-sized DC motors are incredibly user-friendly and cost-effective, working seamlessly with an Arduino or compatible board. Our 10RPM 12Volt DC motors boast a voltage range of 5 to 35V DC, making them suitable for all-terrain robots and an array of robotic applications.

Experience easy connectivity with our motors thanks to the internally threaded shaft and nut, enabling straightforward assembly with wheels and other components. Upgrade your robotic systems today with our efficient and reliable DC-geared motors.

Specifications:

• RPM: Multi RPM (3.5|30|45|60|100|150|200|300|500|750|1000).
• Operating Voltage: 12V DC Max.
• Gearbox: Attached Plastic (spur)Gearbox
• Shaft diameter: 6mm with internal hole
• Torque: 1 kg-cm 
• No-load current = 60 mA(Max)
• Load current = 300 mA(Max).

Features:

1. Our product boasts premium-quality gears, designed for optimal performance and durability.
2. Our metal gears are specially engineered for exceptional wear and tear resistance, ensuring long-lasting use.
3. The gearbox is expertly sealed and lubricated with lithium grease, offering a maintenance-free solution for your needs.
4. Our motor is versatile and adaptable, operating seamlessly from 4V to 12V and delivering a wide range of RPM and torque, with a maximum of 10 RPM at 12V.
5. The shaft features a carefully crafted hole, enabling effortless coupling to other components and ensuring seamless integration into your robotic systems.

Upgrade your robotic systems with our reliable, high-performance motor today.

Note:
1. For desired RPM result we recommend operating this motor on 9v DC. 

2. The color, sticker, and packaging on the product may vary in each lot. We ship randomly.

Package Includes:

1 x Premium: 12V Centre Shaft DC Geared Motor

Premium Quality Multiple RPM DC Gear Robotics Motor 12v 6mm

Discover our Center Shaft DC Geared Motors, engineered with metal gears to deliver exceptional performance. Our DC motors feature a threaded 3mm drill hole in the middle of the shaft, simplifying connectivity to wheels or other mechanical assemblies.

These standard-sized DC motors are incredibly user-friendly and cost-effective, working seamlessly with an Arduino or compatible board. Our 10RPM 12Volt DC motors boast a voltage range of 5 to 35V DC, making them suitable for all-terrain robots and an array of robotic applications.

Experience easy connectivity with our motors thanks to the internally threaded shaft and nut, enabling straightforward assembly with wheels and other components. Upgrade your robotic systems today with our efficient and reliable DC-geared motors.

Specifications:

• RPM: Multi RPM (3.5|30|45|60|100|150|200|300|500|750|1000).
• Operating Voltage: 12V DC Max.
• Gearbox: Attached Plastic (spur)Gearbox
• Shaft diameter: 6mm with internal hole
• Torque: 1 kg-cm 
• No-load current = 60 mA(Max)
• Load current = 300 mA(Max).

Features:

1. Our product boasts premium-quality gears, designed for optimal performance and durability.
2. Our metal gears are specially engineered for exceptional wear and tear resistance, ensuring long-lasting use.
3. The gearbox is expertly sealed and lubricated with lithium grease, offering a maintenance-free solution for your needs.
4. Our motor is versatile and adaptable, operating seamlessly from 4V to 12V and delivering a wide range of RPM and torque, with a maximum of 10 RPM at 12V.
5. The shaft features a carefully crafted hole, enabling effortless coupling to other components and ensuring seamless integration into your robotic systems.

Upgrade your robotic systems with our reliable, high-performance motor today.

Note:
1. For desired RPM result we recommend operating this motor on 9v DC. 

2. The color, sticker, and packaging on the product may vary in each lot. We ship randomly.

Package Includes:

1 x Premium: 12V Centre Shaft DC Geared Motor

Premium Quality Multiple RPM DC Gear Robotics Motor 12v 6mm

Discover our Center Shaft DC Geared Motors, engineered with metal gears to deliver exceptional performance. Our DC motors feature a threaded 3mm drill hole in the middle of the shaft, simplifying connectivity to wheels or other mechanical assemblies.

These standard-sized DC motors are incredibly user-friendly and cost-effective, working seamlessly with an Arduino or compatible board. Our 10RPM 12Volt DC motors boast a voltage range of 5 to 35V DC, making them suitable for all-terrain robots and an array of robotic applications.

Experience easy connectivity with our motors thanks to the internally threaded shaft and nut, enabling straightforward assembly with wheels and other components. Upgrade your robotic systems today with our efficient and reliable DC-geared motors.

Specifications:

• RPM: Multi RPM (3.5|30|45|60|100|150|200|300|500|750|1000).
• Operating Voltage: 12V DC Max.
• Gearbox: Attached Plastic (spur)Gearbox
• Shaft diameter: 6mm with internal hole
• Torque: 1 kg-cm 
• No-load current = 60 mA(Max)
• Load current = 300 mA(Max).

Features:

1. Our product boasts premium-quality gears, designed for optimal performance and durability.
2. Our metal gears are specially engineered for exceptional wear and tear resistance, ensuring long-lasting use.
3. The gearbox is expertly sealed and lubricated with lithium grease, offering a maintenance-free solution for your needs.
4. Our motor is versatile and adaptable, operating seamlessly from 4V to 12V and delivering a wide range of RPM and torque, with a maximum of 10 RPM at 12V.
5. The shaft features a carefully crafted hole, enabling effortless coupling to other components and ensuring seamless integration into your robotic systems.

Upgrade your robotic systems with our reliable, high-performance motor today.

Note:
1. For desired RPM result we recommend operating this motor on 9v DC. 

2. The color, sticker, and packaging on the product may vary in each lot. We ship randomly.

Package Includes:

1 x Premium: 12V Centre Shaft DC Geared Motor

Premium Quality Multiple RPM DC Gear Robotics Motor 12v 6mm

Discover our Center Shaft DC Geared Motors, engineered with metal gears to deliver exceptional performance. Our DC motors feature a threaded 3mm drill hole in the middle of the shaft, simplifying connectivity to wheels or other mechanical assemblies.

These standard-sized DC motors are incredibly user-friendly and cost-effective, working seamlessly with an Arduino or compatible board. Our 10RPM 12Volt DC motors boast a voltage range of 5 to 35V DC, making them suitable for all-terrain robots and an array of robotic applications.

Experience easy connectivity with our motors thanks to the internally threaded shaft and nut, enabling straightforward assembly with wheels and other components. Upgrade your robotic systems today with our efficient and reliable DC-geared motors.

Specifications:

• RPM: Multi RPM (3.5|30|45|60|100|150|200|300|500|750|1000).
• Operating Voltage: 12V DC Max.
• Gearbox: Attached Plastic (spur)Gearbox
• Shaft diameter: 6mm with internal hole
• Torque: 1 kg-cm 
• No-load current = 60 mA(Max)
• Load current = 300 mA(Max).

Features:

1. Our product boasts premium-quality gears, designed for optimal performance and durability.
2. Our metal gears are specially engineered for exceptional wear and tear resistance, ensuring long-lasting use.
3. The gearbox is expertly sealed and lubricated with lithium grease, offering a maintenance-free solution for your needs.
4. Our motor is versatile and adaptable, operating seamlessly from 4V to 12V and delivering a wide range of RPM and torque, with a maximum of 10 RPM at 12V.
5. The shaft features a carefully crafted hole, enabling effortless coupling to other components and ensuring seamless integration into your robotic systems.

Upgrade your robotic systems with our reliable, high-performance motor today.

Note:
1. For desired RPM result we recommend operating this motor on 9v DC. 

2. The color, sticker, and packaging on the product may vary in each lot. We ship randomly.

Package Includes:

1 x Premium: 12V Centre Shaft DC Geared Motor

Premium Quality Multiple RPM DC Gear Robotics Motor 12v 6mm

Discover our Center Shaft DC Geared Motors, engineered with metal gears to deliver exceptional performance. Our DC motors feature a threaded 3mm drill hole in the middle of the shaft, simplifying connectivity to wheels or other mechanical assemblies.

These standard-sized DC motors are incredibly user-friendly and cost-effective, working seamlessly with an Arduino or compatible board. Our 10RPM 12Volt DC motors boast a voltage range of 5 to 35V DC, making them suitable for all-terrain robots and an array of robotic applications.

Experience easy connectivity with our motors thanks to the internally threaded shaft and nut, enabling straightforward assembly with wheels and other components. Upgrade your robotic systems today with our efficient and reliable DC-geared motors.

Specifications:

• RPM: Multi RPM (3.5|30|45|60|100|150|200|300|500|750|1000).
• Operating Voltage: 12V DC Max.
• Gearbox: Attached Plastic (spur)Gearbox
• Shaft diameter: 6mm with internal hole
• Torque: 1 kg-cm 
• No-load current = 60 mA(Max)
• Load current = 300 mA(Max).

Features:

1. Our product boasts premium-quality gears, designed for optimal performance and durability.
2. Our metal gears are specially engineered for exceptional wear and tear resistance, ensuring long-lasting use.
3. The gearbox is expertly sealed and lubricated with lithium grease, offering a maintenance-free solution for your needs.
4. Our motor is versatile and adaptable, operating seamlessly from 4V to 12V and delivering a wide range of RPM and torque, with a maximum of 10 RPM at 12V.
5. The shaft features a carefully crafted hole, enabling effortless coupling to other components and ensuring seamless integration into your robotic systems.

Upgrade your robotic systems with our reliable, high-performance motor today.

Note:
1. For desired RPM result we recommend operating this motor on 9v DC. 

2. The color, sticker, and packaging on the product may vary in each lot. We ship randomly.

Package Includes:

1 x Premium: 12V Centre Shaft DC Geared Motor

Multiple RPM DC Metal Gear Robotics Motor 12v

DC Gear Motors – 12Volts are generally a simple DC motor with a gearbox attached to it. This can be used in all-terrain robots and variety of robotic applications. These motors have a 3 mm threaded drill hole in the middle of the shaft thus making it simple to connect it to the wheels or any other mechanical assembly.

These 12V DC geared motors widely use for robotics applications. Very easy to use and available in standard size. Also, you don’t have to spend a lot of money to control motors with an Arduino or compatible board. The most popular L298N H-bridge module with onboard voltage regulator motor driver can be used with this motor that has a voltage of 12v the most precise motor diver module from the wide range available in our Motor divers category as per your specific requirements.

Specifications and Features:- 

• Operating Voltage: 12V DC
• Gearbox: Attached Plastic (spur)Gearbox
• Shaft diameter: 6mm with internal hole
• Torque: 1 kg-cm 
• No-load current = 60 mA(Max)
• Load current = 300 mA(Max).

Multiple RPM DC Metal Gear Robotics Motor 12v

DC Gear Motors – 12Volts are generally a simple DC motor with a gearbox attached to it. This can be used in all-terrain robots and variety of robotic applications. These motors have a 3 mm threaded drill hole in the middle of the shaft thus making it simple to connect it to the wheels or any other mechanical assembly.

These 12V DC geared motors widely use for robotics applications. Very easy to use and available in standard size. Also, you don’t have to spend a lot of money to control motors with an Arduino or compatible board. The most popular L298N H-bridge module with onboard voltage regulator motor driver can be used with this motor that has a voltage of 12v the most precise motor diver module from the wide range available in our Motor divers category as per your specific requirements.

Specifications and Features:- 

• Operating Voltage: 12V DC
• Gearbox: Attached Plastic (spur)Gearbox
• Shaft diameter: 6mm with internal hole
• Torque: 1 kg-cm 
• No-load current = 60 mA(Max)
• Load current = 300 mA(Max).

Multiple RPM DC Metal Gear Robotics Motor 12v

DC Gear Motors – 12Volts are generally a simple DC motor with a gearbox attached to it. This can be used in all-terrain robots and variety of robotic applications. These motors have a 3 mm threaded drill hole in the middle of the shaft thus making it simple to connect it to the wheels or any other mechanical assembly.

These 12V DC geared motors widely use for robotics applications. Very easy to use and available in standard size. Also, you don’t have to spend a lot of money to control motors with an Arduino or compatible board. The most popular L298N H-bridge module with onboard voltage regulator motor driver can be used with this motor that has a voltage of 12v the most precise motor diver module from the wide range available in our Motor divers category as per your specific requirements.

Specifications and Features:- 

• Operating Voltage: 12V DC
• Gearbox: Attached Plastic (spur)Gearbox
• Shaft diameter: 6mm with internal hole
• Torque: 1 kg-cm 
• No-load current = 60 mA(Max)
• Load current = 300 mA(Max).

Multiple RPM DC Metal Gear Robotics Motor 12v

DC Gear Motors – 12Volts are generally a simple DC motor with a gearbox attached to it. This can be used in all-terrain robots and variety of robotic applications. These motors have a 3 mm threaded drill hole in the middle of the shaft thus making it simple to connect it to the wheels or any other mechanical assembly.

These 12V DC geared motors widely use for robotics applications. Very easy to use and available in standard size. Also, you don’t have to spend a lot of money to control motors with an Arduino or compatible board. The most popular L298N H-bridge module with onboard voltage regulator motor driver can be used with this motor that has a voltage of 12v the most precise motor diver module from the wide range available in our Motor divers category as per your specific requirements.

Specifications and Features:- 

• Operating Voltage: 12V DC
• Gearbox: Attached Plastic (spur)Gearbox
• Shaft diameter: 6mm with internal hole
• Torque: 1 kg-cm 
• No-load current = 60 mA(Max)
• Load current = 300 mA(Max).

12Volt N20 Mini Motor

These N20 12V Micro Metal Gear Motor With Encoder is intended for use at 12 V. Though in general, these kinds of motors can run at voltages above and below this nominal voltage; so they should comfortably operate in the 3 – 12 V range (rotation can start at voltages as low as 0.5 V).

Lower voltages might not be practical, and higher voltages could start negatively affecting the life of the motor. The micro metal gear motors are available in a wide range of gear ratios—from 5:1 up to 1000:1. With the exception of 1000:1 gear ratio versions, all of the micro metal gear motors have the same physical dimensions; so one version can be easily swapped for another if your design requirements change.

Features :

1. Model: GA12 N20.
2. This is a DC Mini Metal Gear Motor, ideal for making robots
3. Lightweight, high torque and low RPM.
4. Fine craftsmanship, durable, not easy to wear.
5. With excellent stall characteristics, can climb hills easily.
6. You can also easily mount a wheel on the motor’s output shaft.
7. Motor Size: 15 x 12 x 10 mm.
8. Gearbox Length: 9 mm.
9. Count: 3PPR(Pulse per Revolutions).

How to wiring? :

1. Red – motor Power  (Exchange can control the motor positive and negative rotation).
2. Black – encoded power supply(VCC) – Positive (positive 3.3-5v).
3. Yellow – signal feedback (motor turns 2 signals).
4. Green – signal feedback (motor turns 2 signals).
5. Blue – encoded power(GND).
6. White – Motor power (Exchange can control the motor positive and negative rotation).

Dimensions :

12Volt N20 Mini Motor

These N20 12V Micro Metal Gear Motor With Encoder is intended for use at 12 V. Though in general, these kinds of motors can run at voltages above and below this nominal voltage; so they should comfortably operate in the 3 – 12 V range (rotation can start at voltages as low as 0.5 V).

Lower voltages might not be practical, and higher voltages could start negatively affecting the life of the motor. The micro metal gear motors are available in a wide range of gear ratios—from 5:1 up to 1000:1. With the exception of 1000:1 gear ratio versions, all of the micro metal gear motors have the same physical dimensions; so one version can be easily swapped for another if your design requirements change.

Features :

1. Model: GA12 N20.
2. This is a DC Mini Metal Gear Motor, ideal for making robots
3. Lightweight, high torque and low RPM.
4. Fine craftsmanship, durable, not easy to wear.
5. With excellent stall characteristics, can climb hills easily.
6. You can also easily mount a wheel on the motor’s output shaft.
7. Motor Size: 15 x 12 x 10 mm.
8. Gearbox Length: 9 mm.
9. Count: 3PPR(Pulse per Revolutions).

How to wiring? :

1. Red – motor Power  (Exchange can control the motor positive and negative rotation).
2. Black – encoded power supply(VCC) – Positive (positive 3.3-5v).
3. Yellow – signal feedback (motor turns 2 signals).
4. Green – signal feedback (motor turns 2 signals).
5. Blue – encoded power(GND).
6. White – Motor power (Exchange can control the motor positive and negative rotation).

Dimensions :

12Volt N20 Mini Motor

These N20 12V Micro Metal Gear Motor With Encoder is intended for use at 12 V. Though in general, these kinds of motors can run at voltages above and below this nominal voltage; so they should comfortably operate in the 3 – 12 V range (rotation can start at voltages as low as 0.5 V).

Lower voltages might not be practical, and higher voltages could start negatively affecting the life of the motor. The micro metal gear motors are available in a wide range of gear ratios—from 5:1 up to 1000:1. With the exception of 1000:1 gear ratio versions, all of the micro metal gear motors have the same physical dimensions; so one version can be easily swapped for another if your design requirements change.

Features :

1. Model: GA12 N20.
2. This is a DC Mini Metal Gear Motor, ideal for making robots
3. Lightweight, high torque and low RPM.
4. Fine craftsmanship, durable, not easy to wear.
5. With excellent stall characteristics, can climb hills easily.
6. You can also easily mount a wheel on the motor’s output shaft.
7. Motor Size: 15 x 12 x 10 mm.
8. Gearbox Length: 9 mm.
9. Count: 3PPR(Pulse per Revolutions).

How to wiring? :

1. Red – motor Power  (Exchange can control the motor positive and negative rotation).
2. Black – encoded power supply(VCC) – Positive (positive 3.3-5v).
3. Yellow – signal feedback (motor turns 2 signals).
4. Green – signal feedback (motor turns 2 signals).
5. Blue – encoded power(GND).
6. White – Motor power (Exchange can control the motor positive and negative rotation).

Dimensions :

12Volt N20 Mini Motor

These N20 12V Micro Metal Gear Motor With Encoder is intended for use at 12 V. Though in general, these kinds of motors can run at voltages above and below this nominal voltage; so they should comfortably operate in the 3 – 12 V range (rotation can start at voltages as low as 0.5 V).

Lower voltages might not be practical, and higher voltages could start negatively affecting the life of the motor. The micro metal gear motors are available in a wide range of gear ratios—from 5:1 up to 1000:1. With the exception of 1000:1 gear ratio versions, all of the micro metal gear motors have the same physical dimensions; so one version can be easily swapped for another if your design requirements change.

Features :

1. Model: GA12 N20.
2. This is a DC Mini Metal Gear Motor, ideal for making robots
3. Lightweight, high torque and low RPM.
4. Fine craftsmanship, durable, not easy to wear.
5. With excellent stall characteristics, can climb hills easily.
6. You can also easily mount a wheel on the motor’s output shaft.
7. Motor Size: 15 x 12 x 10 mm.
8. Gearbox Length: 9 mm.
9. Count: 3PPR(Pulse per Revolutions).

How to wiring? :

1. Red – motor Power  (Exchange can control the motor positive and negative rotation).
2. Black – encoded power supply(VCC) – Positive (positive 3.3-5v).
3. Yellow – signal feedback (motor turns 2 signals).
4. Green – signal feedback (motor turns 2 signals).
5. Blue – encoded power(GND).
6. White – Motor power (Exchange can control the motor positive and negative rotation).

Dimensions :

12Volt N20 Mini Motor

These N20 12V Micro Metal Gear Motor With Encoder is intended for use at 12 V. Though in general, these kinds of motors can run at voltages above and below this nominal voltage; so they should comfortably operate in the 3 – 12 V range (rotation can start at voltages as low as 0.5 V).

Lower voltages might not be practical, and higher voltages could start negatively affecting the life of the motor. The micro metal gear motors are available in a wide range of gear ratios—from 5:1 up to 1000:1. With the exception of 1000:1 gear ratio versions, all of the micro metal gear motors have the same physical dimensions; so one version can be easily swapped for another if your design requirements change.

Features :

1. Model: GA12 N20.
2. This is a DC Mini Metal Gear Motor, ideal for making robots
3. Lightweight, high torque and low RPM.
4. Fine craftsmanship, durable, not easy to wear.
5. With excellent stall characteristics, can climb hills easily.
6. You can also easily mount a wheel on the motor’s output shaft.
7. Motor Size: 15 x 12 x 10 mm.
8. Gearbox Length: 9 mm.
9. Count: 3PPR(Pulse per Revolutions).

How to wiring? :

1. Red – motor Power  (Exchange can control the motor positive and negative rotation).
2. Black – encoded power supply(VCC) – Positive (positive 3.3-5v).
3. Yellow – signal feedback (motor turns 2 signals).
4. Green – signal feedback (motor turns 2 signals).
5. Blue – encoded power(GND).
6. White – Motor power (Exchange can control the motor positive and negative rotation).

Dimensions :

12Volt N20 Mini Motor

These N20 12V Micro Metal Gear Motor With Encoder is intended for use at 12 V. Though in general, these kinds of motors can run at voltages above and below this nominal voltage; so they should comfortably operate in the 3 – 12 V range (rotation can start at voltages as low as 0.5 V).

Lower voltages might not be practical, and higher voltages could start negatively affecting the life of the motor. The micro metal gear motors are available in a wide range of gear ratios—from 5:1 up to 1000:1. With the exception of 1000:1 gear ratio versions, all of the micro metal gear motors have the same physical dimensions; so one version can be easily swapped for another if your design requirements change.

Features :

1. Model: GA12 N20.
2. This is a DC Mini Metal Gear Motor, ideal for making robots
3. Lightweight, high torque and low RPM.
4. Fine craftsmanship, durable, not easy to wear.
5. With excellent stall characteristics, can climb hills easily.
6. You can also easily mount a wheel on the motor’s output shaft.
7. Motor Size: 15 x 12 x 10 mm.
8. Gearbox Length: 9 mm.
9. Count: 3PPR(Pulse per Revolutions).

How to wiring? :

1. Red – motor Power  (Exchange can control the motor positive and negative rotation).
2. Black – encoded power supply(VCC) – Positive (positive 3.3-5v).
3. Yellow – signal feedback (motor turns 2 signals).
4. Green – signal feedback (motor turns 2 signals).
5. Blue – encoded power(GND).
6. White – Motor power (Exchange can control the motor positive and negative rotation).

Dimensions :

12Volt N20 Mini Motor

These N20 12V Micro Metal Gear Motor With Encoder is intended for use at 12 V. Though in general, these kinds of motors can run at voltages above and below this nominal voltage; so they should comfortably operate in the 3 – 12 V range (rotation can start at voltages as low as 0.5 V).

Lower voltages might not be practical, and higher voltages could start negatively affecting the life of the motor. The micro metal gear motors are available in a wide range of gear ratios—from 5:1 up to 1000:1. With the exception of 1000:1 gear ratio versions, all of the micro metal gear motors have the same physical dimensions; so one version can be easily swapped for another if your design requirements change.

Features :

1. Model: GA12 N20.
2. This is a DC Mini Metal Gear Motor, ideal for making robots
3. Lightweight, high torque and low RPM.
4. Fine craftsmanship, durable, not easy to wear.
5. With excellent stall characteristics, can climb hills easily.
6. You can also easily mount a wheel on the motor’s output shaft.
7. Motor Size: 15 x 12 x 10 mm.
8. Gearbox Length: 9 mm.
9. Count: 3PPR(Pulse per Revolutions).

How to wiring? :

1. Red – motor Power  (Exchange can control the motor positive and negative rotation).
2. Black – encoded power supply(VCC) – Positive (positive 3.3-5v).
3. Yellow – signal feedback (motor turns 2 signals).
4. Green – signal feedback (motor turns 2 signals).
5. Blue – encoded power(GND).
6. White – Motor power (Exchange can control the motor positive and negative rotation).